- 您现在的位置：买卖IC网 > Sheet目录223 > ESD11N5.0ST5G (ON Semiconductor)TVS BIDIR 250MW 5V DSN2
ESD11N5.0ST5G
It is imperative that the coating is conformal, uniform, and
free of impurities to insure a consistent mounting process.
Due to the package’s extremely small size, we only
recommend the use of the electroless nickel/ immersion gold
metallization over the copper pads.
PCB Circuit Trace Width
The width of the PCB circuit trace plays an important role
in the reduction of component tilting when the solder is
reflowed. A solderable circuit trace allows the solder to wick
or run down the trace, reducing the overall thickness of the
solder on the PCB and under the component. Due to the
small nature of the solder pad and component, the solder on
the PCB will tend to form a bump causing the component to
slide down the side of that solder bump resulting in a tilted
component on the PCB. Allowing the solder to wick or run
down the PCB circuit trace, will reduce the solder thickness
and in turn prevent the solder from forming a ball on the PCB
pad. This was observed during ON Semiconductor board
mounting evaluations. The best results to prevent tilting
used a PCB circuit trace equal to the width of the mounting
pad. The length of the solder wicking or run out is controlled
by the solder mask opening.
Solder Type
Solder pastes such as Cookson Electronics’ WS3060 with
a Type 4 or smaller sphere size are recommended. WS3060
has a water-soluble flux for cleaning. Cookson Electronics’
PNC0106A can be used if a no-clean flux is preferred.
Solder Stencil Screening
Stencil screening of the solder paste onto the PCB is
commonly used in the industry. The recommended stencil
thickness for this part is 0.1 mm (0.004 in). The sidewalls of
the stencil openings should be tapered approximately five
A second stencil option is shown in Figure 10. This option
increases the amount of solder paste applied to the PCB
through the stencil. This second option increases the stencil
opening size and pitch. The PCB mounting pads and solder
mask opening on the board do not change from the
recommendations in Figure 6.
Figure 10. Maximum Stencil Pattern
Note: If the maximum stencil opening option from
Figure 10 is used, tilt may occur on some of the packages.
This was evident in the board mounting study we conducted.
The stencil with the largest openings may improve solder
release from the stencil along with slightly increasing the
package shear strength.
Package Placement
Due to the small package size and because the pads are on
the underside of the package, an automated pick and place
procedure with magnification is recommended. A dual
image optical system where the underside of the package can
be aligned to the PCB should be used. Pick and place
equipment with a standard tolerance of +/- 0.05 mm (0.002
in) or better is recommended. The package self aligns during
the reflow process due to the surface tension of the solder.
degrees along with an electro-polish finish to aid in the
release of the paste when the stencil is removed from the
PCB. See Figure 9 for the recommended stencil opening size
and pitch shown on the recommended PCB mounting pads
and solder mask opening from Figure 6.
Figure 9. Recommended Stencil Pattern.
http://onsemi.com
5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ESD1P0RFWE6327
DIODE RF ESD 1CH SOT323
ESD3V3U1U-02LS E6327
DIODE TVS 3.3V TSSLP-2-1
ESD3V3U4ULC E6327
DIODE TVS 3.3V TSLP-9-1
ESD4238MTTAG
IC ESD CLAMP ARRAY 8CH 16-WDFN
ESD5384NCTBG
DIODE ESD PROTECT 4CH 9-WLCSP
ESD5B5.0ST1G
TVS BIDIRECT 50W SOD523
ESD5V0H1U-02LS E6327
DIODE TVS UNI-DIRECT 5V TSSLP-2
ESD5V0L1B-02V H6327
DIODE TVS BIDIR 5V SC79-2-1
相关代理商/技术参数
ESD11V120
制造商:Panasonic Industrial Company 功能描述:SWITCH
ESD11V130
制造商:Panasonic Industrial Company 功能描述:SWITCH
ESD11V220
制造商:Panasonic Industrial Company 功能描述:SWITCH
ESD11V220K
制造商:Panasonic Industrial Company 功能描述:SWITCH
ESD11V230
制造商:Panasonic Industrial Company 功能描述:SWITCH
ESD12.00000F20B33
制造商:HOSONIC ELECTRONIC 功能描述:ESD Series 12mhz 20PF +/-30ppm HC49SMB package Crystal
ESD1201B2C
制造商:WEITRON 制造商全称:Weitron Technology 功能描述:Surface Mount TVS For ESD Protection Diode
ESD1204
制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:Bourns Releases New Power TVS (PTVS) Products